Steel Research International
Publisher: Wiley · ISSN 16113683 · 15 articles
-
Thermomechanical Modeling and Irreversible Deformation Analysis of a Ruhrstahl–Heraeus Degasser Lower Vessel Refractory Lining
The thermomechanical behavior of the sidewall of a Ruhrstahl–Heraeus (RH) degasser lower vessel under cyclic operation is studied using finite element modeling approach. Two distinct constitutive material models are applied to...
-
Hierarchical Microstructures Enable Exceptional Strength‐Ductility Synergy in Tempering‐Quenching‐Partitioning‐Tempering Treated Steel
A hierarchical multiphase microstructure consisting of soft phases (primary martensite (PM) and highly stable retained austenite (RA)) and hard phases (secondary martensite (SM) and lower bainite (LB)) is engineered in a high‐carbon...
-
Ti Microalloying Enhances Corrosion Resistance of HRB600E Seismic Rebar in Three Typical Marine Corrosion Stages
HRB600E high‐strength seismic rebar is widely used in critical infrastructure, where its strength–toughness and corrosion resistance are essential for structural safety. The corrosion failure of rebar is a progressive multistage process...
-
Study on High‐Temperature Oxidation Behavior of Cu‐Containing HTRCr Heat‐Resistant Cast Iron
The high‐temperature oxidation behavior of Cu‐containing HTRCr heat‐resistant cast iron in air at 500–900 °C was investigated. The oxide species on the surface of the oxidized material were calibrated using the X‐ray diffractometer...
-
Nitrogen and Recrystallization Effects in 316LN Steel: Microstructure Evolution and Cryogenic Deformation
Austenitic stainless steels (ASSs) are widely used in civilian and defense applications due to their excellent corrosion resistance and formability; however, their relatively low yield strength restricts cryogenic service. Here, 316LN...
-
Effect of Heterogeneous Austenite and Multiscale B2 Precipitates on the Strength–Ductility Balance of Fe–Mn–Al–C–Ni Lightweight Steel
A Fe–29Mn–9Al–1C–6Ni (wt%) lightweight steel is processed by hot rolling followed by solution and aging treatments to obtain a heterogeneous austenitic microstructure containing NiAl‐type B2 precipitates. Microstructural...
-
Simulation of Solidification Microstructure in F45MnVS Non‐Quenched and Tempered Steel Continuous Casting Billets Based on the CAFE Method
To characterise the microstructural evolution during solidification of F45MnVS non‐quenched and tempered steel, a microstructure prediction model for continuous casting billets is developed using the cellular automaton–finite element...
-
In Situ Kinetic Study on Phase Transformations During the Annealing of Ductile Iron Pipes
Ductile iron pipes (DIPs) are widely used in water supply networks, and their microstructure and performance are strongly influenced by the annealing process. Previous studies have mainly focused on isothermal transformations during the...
-
Impact of AC Frequency and Slag Composition on Inclusion Entrapment in Electroslag Remelting
A transient numerical model is developed to investigate the influence of AC frequency and slag properties on the transport and entrapment of exogenous and endogenous nonmetallic inclusions (NMIs) during electroslag remelting. The model...
-
Effect of Si Content on Microstructure and Tensile Properties of Fe–Mn–Al–C Lightweight Steel
Fe–Mn–Al–C lightweight steels are promising candidates for weight‐sensitive structural components. However, the role of compositional tailoring in governing strength–ductility synergy remains to be fully clarified. In this study,...
-
Mitigation Effect of Internal Hydrogen on External Hydrogen‐Induced Embrittlement in Austenitic Lightweight Steel
The influence of various hydrogen environments on the hydrogen embrittlement behavior of Fe‐30Mn‐8.6Al‐C austenitic lightweight steel was investigated using slow strain rate tensile tests. Under the experimental conditions adopted in...
-
Deformation Behavior and Microstructural Evolution of 20Cr13/3003 Steel–Aluminum Composite Plates at Different Temperatures
Tensile tests were conducted on 20Cr13/3003 steel–aluminum composite plates, comprising 20Cr13 martensitic stainless steel and 3003 Al─Mn alloy, at temperatures ranging from 25 to 300 °C using a Shimadzu AGX‐V 100 kN universal testing...
-
A Physical Model for Nucleation and Grain Growth During Static Recrystallization in Steel
A physical model is proposed that describes the evolution of grain size after hot deformation of steel with an austenitic structure. Unlike previous models, the growth kinetics of new and old grains are described by two separate...
-
Oxide Scale Decomposition‐Driven Intergranular Oxidation in Hot‐Rolled Hot Stamping Steel: Mechanism and Process Control
Intergranular oxidation (IGO) in 22MnB5 steel degrades automotive component performance, yet oxygen supply mechanisms under low oxygen potentials remain unclear. This study reveals that IGO occurs exclusively below 900 °C, with the...
- Front Cover (steel research int. 11/2026)