JOM
Издатель: Springer Nature · ISSN 1047-4838,1543-1851 · 1770 статей
- Effect of Strain Rate on Evolution of Inclusion and Microstructure in Ti-Zr Deoxidized Low-Carbon Microalloyed Steel
- Comprehensive Utilization Technology and Application of Total Resources from Ultra-Low-Grade Vanadium–Titanium Magnetite: A Case Study of Chengde, China
- Effects of Cr2O3 and MnO on the Melting and Rheological Properties of High-Alumina Slag Containing 30 wt.% Al2O3
- Green Separation of Ag-Sb-Bi Alloy: Vacuum Distillation and M-MIVM Model Validation
- Powder Metallurgy Processed Graphite and ZrSiO4 Reinforced Fe-Cu/BaSO4 Sintered Composites for Wind Turbine Friction Applications
- Effect of Impurities on the Hydrogen Reduction Kinetics of High-Phosphorus Iron Ore: Insights from a Hematite-Based Comparative Analysis
- Experimental Measurements of the Effect of Cold Plasma Exposure Time on the Preparation of Iron Oxide Nanoparticles for Gas-Sensing Applications
- Synergistic Recovery of Nickel and Iron from Laterite Ore and Sintering Red Mud via Co-reduction Process: Kinetics and Mechanism
- Microstructure Reconfiguration of Roll-Casting 6061 Alloy by In Situ Magnetic Field with Various Directions and Frequencies
-
Wear Behavior of TiB2–C3N4 Composites Fabricated by SPS Process
Abstract Ultra-high-temperature ceramics (UHTCs), particularly titanium diboride (TiB 2 ), are critical for demanding applications such as thermal protection systems, wear-resistant components, and high-temperature applications....
- Microstructure-Driven Frequency-Dependent Properties of Soft Lead Zirconate Titanate Ceramics (x = 0.52)
- Microstructure and Mechanical Properties of Dissimilar Joints Between Titanium Alloy and Stainless Steel
- Controlled Preparation of High-Quality Ti(Cx, N1-x) Powders with Low Oxygen Content
- Efficient Iron Extraction from Refractory Limonite Ores Using the Preconcentration-Suspension Magnetization Roasting-Magnetic Separation Process: A Pilot-Scale Study
- Purification of Metallurgical-Grade Silicon by Solvent Refining Using Si–Zn Alloy
- Phase Equilibria and Copper–Silver-Substituted Solid Solutions in the Cu2S-Ag2S-GeS2 System
- Tribological and Corrosion Performance of Plasma-Sprayed Cr2O3–TiO2 Composite Coatings
- Study on the Influence of CMT Welding Parameters on the Microstructure and Friction-Wear Properties of Babbitt Alloy
- Multi-Scale Modeling of Dynamic Recrystallization During Friction Stir Welding of Aluminum Alloy Considering Dwell and Welding Stages
- Fundamental Study on Clean Deoxidation Process: Ascending Behavior of Hydrogen Bubble in Molten Steel
- A Novel (HfTaZrTiV) C High-Entropy Ceramic with Submicron Grains: Role of Graphite and Si Additives
- Research on the Sodium Storage Performance of SnS@CNT as Anode Materials for Sodium-Ion Batteries
- Research Progress of Machine Learning and Deep Learning Applications in the Context of Blast Furnace Intelligence
- Process Optimization Design of Needle-Punched Composite Preforms Based on Machine Learning
-
University Laboratory-Scale Carbon Footprint and Cost Comparison of Atomized and Short-Chip-Milled Aluminum Powders for TPU–Al Composite Specimens
Abstract This study compares the cradle-to-gate carbon footprint and production cost of TPU–Al composite specimens manufactured by fused filament fabrication (FFF) using two aluminum-powder sourcing routes: commercial gas-atomized...
- Recycling of Superalloy Scrap Through VIM-VAR: Cleanliness, Microstructure, Mechanical Properties
- Investigating the Influence of Gas Composition on the Reduction Kinetics of Iron Oxide Briquettes
- Optimization of Laser Welding Process of AISI444 Ferritic Stainless-Steel Sheet Based on Response Surface Method
- Unraveling the Interplay Between Interfacial Behavior and Performance in Nano-Al2O3/Al Composites via Electron Work Function (EWF) Methodology
- Study on the Softening–Melting Behavior of Ferrous Burden with Different Characteristics Under Hydrogen-Rich Blast Furnace